Call Today

 

The content following next about How to Install a Bathtub is really remarkable. You should keep reading.

Installing a tub isn't specifically rocket science, yet it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably tough job. If the old bathtub is conveniently obtainable, the job can relocate speedily; if you have to open a wall to remove the old tub and place the new tub, the task is a lot harder. In either instance, the task is within a home handyman's abilities, although you will need a helper to vacate the old tub and also set in the brand-new one. Make certain you have actually certified yourself for the job and are comfortable attempting it. As opposed to employing a specialist to take control of a halfway-completed task, it is far better to consider employing one before you begin. Opportunities are you might need an expert plumber to make tube connections.
This article will certainly aid you mount a brand-new bath tub in your washroom if you have already acquired a brand-new tub and also don't require to change the arrangement of your previous water pipes.
Your devices as well as product list ought to consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Getting ready for the Setup

To start with, the sustaining frame provided with the bathroom must be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to stop stress on the tub.
Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its last setting.

 

 

Removing Old Touches

If you need to change old taps with new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, turn on the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be quite problematic as a result of the restricted accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipes. Once the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Setting up the Bathtub

Using the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the bathtub until the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipeline by making a compression join; then do the same for the various other faucet.
Turn on the supply of water and also inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as likewise check the overflow outlet and the typical electrical outlet for leakages.
Ultimately, fix the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the bathtub ought to wait until the bathtub has been made use of a minimum of once as this will certainly settle it right into its last setting.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making certain that the washing machines are in place in between the tap and also the sink. Safeguard the faucet in position with the manufacturer supplied backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The previous type must be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bathtub

In the area where the bath satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a rigid seal, creating the water to permeate the wall surface in between the bathroom as well as the tiling, leading to issues with moisture as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, as well as can sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to allow for the movement experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly offered on the market. It is recommended to fit the floor tiles using water-resistant or water resistant sticky and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We are very interested in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you liked the new post. Make sure you set aside a second to distribute this blog posting if you liked it. Thanks a lot for your time. Please come by our site back soon.

Reliable plumber? Dial now!